How to Care for Strong Acid Cation Exchange Resins - Hydrogen Cycle
Resins are usually delivered in the sodium form.
- Exhaust the resin by passing 2 BV of 4% NaOH through a column of resin at a rate of 2 BV/h
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Regenerate the resin by passing 4 BV of HCl or H2SO4 through a column of resin at a flow rate of 2 BV/h
- 5 BV 5% HCl = 5.5 eq/lBV
- 5% H2SO4 = 4.1 eq/l
4. Rinse the resin with 5 BV of DI water at a flow rate of 2 BV/h
5. Repeat the above procedure at least once.
BV refers to the volume of resin used.
For example, if using one liter of resin, then 1 BV (or 1 bed volume) equals one liter.
How to Care for Strong Acid Cation Resins - Sodium Cycle
- Exhaust the resin with raw water by passing 6 BV of 2% CaCl2 solution at a flow rate of 2 BV/h = 2.2 eq/l
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Regenerate the resin by passing 2 BV of 10% NaCl at a rate of 2 BV/h
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Repeat the above process at least once
How to Care for Weak Acid Cation Exchange Resins
Resins are usually delivered in the hydrogen form.
- Exhaust the resin by passing 5 BV of 4% NaOH hrough a column of the resin at a rate of 2 BV/h (a dosage equivalent to 5 eq/L). There is potentially high volume change for weak acid cation (WAC) resins in changing from hydrogen to sodium form.
Examples:
Purolite™ C104Plus 60%, Purolite C115E 100%
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Regenerate the resin by passing 5 BV of 5% HCl or 5% or H2SO4 at a rate of 2 BV/h
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Repeat above procedure at least once
Note: 1 BV = 1 liter of water running through 1 liter of resin or 7.48 US gallons through 1 ft³ of resin.
How to Care for Strong Base Anion Exchange Resins
Resins are usually delivered in the salt (exhausted) form.
- Regenerate the resin by passing 3 BV of 4% NaOH through a column of resin
at a rate of 2 BV/h
- Rinse with 5 BV DI water at a rate of 2 BV/h
- Exhaust with 2 BV of 4% HCI or H2SO4 solution (Note: acid solution can be replaced with NaCI solution)
- Rinse again
How to Care for Weak Base Anion Exchange Resins
Resins are usually delivered in the free-base form.
- Exhaust the resin by passing 2 BV of 5% HCl or 5% H2SO4 at a rate of 2 BV/h through a column of the resin
- Rinse with 5 BV DI water at a rate of 2 BV/h
- Regenerate the resin by passing 3 BV of 5% NaOH or 5% NH4OH at a rate of 2 BV/h
- Rinse with 5 BV of DI water at a rate of 2 BV/h
- Repeat the above process at least twice
How to Care for NSF/ANSI 44 & NSF/ANSI 61 Certified Resins
Please refer to the WQA website for pre-use directions.
How to Care for PraestoTM SP200 Agarose Resin
Before use, Praesto SP200 should be prepared by the following procedure.
- Equilibrate out of shipping buffer into packing buffer - typically 400 mM NaCl.
- Pack the column according to Purolite Praesto packing instructions.
- Once packed, rinse with 2-5 bed volumes of 400 mM NaCl.
- Rinse with 2-5 bed volumes of water or running buffer as required for the purification process.
Cleaning should be carried out regularly, as a wash with 2-5 bed volumes of 0.5 M NaOH followed by neutralization with 0.1 M acetate and a 2-5 bed volume re-equilibration into water or running buffer.
_____________________________________________________________________________________________________
It is strongly recommended that the product water is tested and confirmed to be fully in specification before it is used for direct human consumption or for the intended food treatment.
Note: Depending on storage time and conditions, additional pre-treatment may be required.
